cisco ccie routing and switching v5 0 troubleshooting practice labs - SPOTO CCIE CLUB

  • 1. TS: 2 sets topology, TS1 Ts2
  • 2. DIAG: 8sets
  • 3. CFG: 3sets topology,H1 CFG,H1+CFG,H2 CFG,H2+CFG,H3 CFG
    1) TS:TS have 2 topology, TS1 and TS2,you will face one of them on exam ,our TS include all of the faults on exam.
    2) DIAG:DIAG have 8 Sets, you will face one of them.
    3) CFG:CFG have 2 topology,every topology include 2 Sets CFG,so you need practice 4 Sets CFG. We call H1 CFG、H1+ CFG、H2 CFG、H2+ CFG.
    H1 CFG and H1+ CFG 95% are the same. just some request is different.
    H2 CFG and H2+ CFG 85% are the same ,just some request is different.
    H3 CFG is new CFG.

Feedbacks More>>

Do you know how to solve TS /CFG problems?

There are not many problems with the exam. I will Just write something I think I need to pay
attention to. with the help of SPOTO club, i pass the exam once. If you want to know more details,
you can consult SPOTO club where there are many professionals. I will provide comprehensive
dumps and clear solutions.

TS:
1. User 4 trace 10.4.40.40. Only when I come back to check, I find trace 10.4.40.40 timeout
suddenly. In the beginning, it is good. but It is ping, not trace. R40 trace usser4 also works. Finally,
I reload user4, then the phenomenon is restored. So, if you have a chance, you still have to look
at what you have done.
2.MPLS backup. The backup enterprise is required to go to DMVPN. I take half an hour to try to
do this. I discover that DMVPN will become the primary route if I can’t use some ways. There is
no default route-map on r14. I remember that the teacher advises us not to write route-map. So
give up. Finally, I change the configuration back. only r51 OS has a devolved default route in TS. In
65005, master and standby can be distinguished by setting default-information to originate
metric-type. Do not know how to distinguish between primary and secondary in 65001. There is
no route-map preset on r14.

CFG:
Layers 1 and 2 do require more attention. There is no SW mo acc, there is also the mouth of the
shutdown. Remember to take the time to check yourself.
2 many kids are missing. Take the time to look it up.
3.HSRP has been partially configured.
I want to give some confidence to many students like me who work full-time and have no time to
knock out the version on weekends. It is really important to watch the discussion in the group
and listen to the teachers teaching videos carefully. Many of the situations I encountered in the
exam room are solved in groups and by teachers. In addition, if there is no time for students, you
can try to take a week off work before the test or take participate in the model test. I always talk
to the teacher after the exam. My teacher has been very helpful to me. They help me understand
the test point. Finally, thank you very much for your help!

Read More >>

CCIE RS Lab solutions:TS2, DIAG2+, CFG 2+

Combination: TS2, DIAG2+, CFG 2+. Test location: BJ
Q1 Deny all by default, add one to release.
Q2 R14: next-version op-self
Q3 Did not solve it, give up decisively, R23 had a neighbor but did not receive the
route of 10.2.100/24, IGP checked no problem and BGP strategy was no problem,
too.
Q4 The demand has indeed changed, not SERVER1, but SERVER2, the solution is
consistent.
Q5 Change the network type of the tunnel to P2M. Note here that the R60
phenomenon map requires a route of 10.100.0.51. I didn’t pay attention to it for the
first time. There is a problem with the tunnel IP address of R51 (/32).
Q6 Do Redis OSPF in R15 ipv6.
Q7 R1 did not announce the IGP; the RT import of R3 had a problem, I checked
R4/R6 and changed it to the correct one.
Q8 D version CP snooping, add a trust, and then remove the lease of D version CP.
Q9 Tunnel key is wrong
Q10 Supplement the R24’s outside configuration and add R25 in parallel. (The
address of telnet is 123.45.67.89).

DIAG2+
Just starting this, it’s really awkward, I don’t know what to do. Because you can’t
easily click “next”, I probably guessed that the answer might be DIAG2. After the
next question, I found that I can take a step forward.
Look at the picture and see the configuration.
Found that R2 has no route, R3 has a route.
After looking at the topology, I found that this topology was the opposite of the
version 2+ topology. I subconsciously thought it was version 2, but later confirmed
that there was a problem with R2, which was DIAG2+; the problem with R3 was
DIAG2. Decisively chose the answer of DIAG2+.
The capture file has a link at the bottom of the test interface. After you click it, it
will come out (the same as the cloud version ark given by the teacher).
Here, I personally analyze where the capture is very embarrassing. Filtering with the
version SRPV6 first does not work. It is filtered out using the version srp later. I have
been looking for a long time, I am very embarrassed, I don’t know which one to
choose. Finally, I stared at the FE80 package. Note that it is the src column. Don’t
find the dst column, confirm it and choose it. (The one of the FE80 that I chose dst
at the beginning).

CFG 2+
When I got the version, I was so happy that it was so simple!
OSPF is basically pre-configured. When configuring DR/BDR, pay attention to “cle ip ospf pro”.
BGP is also full, the router-id can be added up.
All of Corenetwork’s VRFs don’t have RDs.
JacobsCorp’s VRF is also equipped with its own.
————Pick up your sleeves and do it!
Maybe I knocked too fast. When I was typing 2.4 EBGP, I did all of MPLS, VPNV4,
VRF, and RT (version Q, Main office). I admire myself and dare to do this. I suggest
that you don’t do this like me. In the end, you still have to slash all the way and
stabilize! Because it is in this process, I was added to the wrong point by the
teacher, and I will talk about it in detail later!
When I did DMVPN, I didn’t have any “fragile ingredients”. It was just a casual
down, just add IPSEC.
Today, BJ’s Andy teacher is too strict. I will elaborate on my experience with TR (I
remembered it three times at first, then calmly thought about it not only three
times).
The first place: The IGP of R15 is all gone. At this time, when I configured EBGP of
R15, I habitually checked the neighbors and configuration of IGP and found this
problem.

Note: Recovery after reconfiguration.
The second place: the IP address of R52 was changed (not pre-configured, because

I confirmed it is “up” when I configured).
Note: Recovery after reconfiguration.
The third place: the RD of the R52 was changed. Neighbors were all hanging, I
reconfigured them all.

Note: Recovery after reconfiguration.
The fourth place: R19’s DMVPN IPSEC strategy.
Note: Modify algorithm.
The fifth place: Multicast can’t come up. When I fix the configuration, I just added
the configuration, he removed it in the next second. (Change the global configuration of R17).
Note: Reconfigured, “shut” “no shut”, still does not work. In the end, I was
courageous and reloaded R17 directly. Restart the card for nearly 4 minutes,
fortunately, dmvpn is fine. Be sure to confirm the various configurations: Is the track
of IGP, NAT, SW3/SW4 recovered?
The sixth place: the EBGP status of R16 became idle.
Note: Recovery after reconfiguration.
Before the volume was handed over, I saved the windows one by one. I confirmed
the phenomena of the main and standby paths and the maps given by all the test
sites. But before the results came out, my heart was hung.
Finally, express my feelings, “Calmly take care of everything that happens, and have
a good mentality.” You have to understand the biscuit teacher’s problem-solving ideas.
Matters needing attention (personal position):
First, put the key equipment on the display, when all the configuration is checked,
put the key equipment in the lower part of the display and do a check in five
minutes! Avoid being TR and don’t know.
Second, the seat has two displays, it is recommended that you prepare for the split
screen operation during the preparation period. (Clicking on the device defaults to
the left screen, pulling all the questions to the right screen, making it a lot smoother)
Third, do not easily restart some important equipment, this is not recommended.
Because there are likely to be some unexpected situations!
Fourth, the night before the test, do not eat spicy food.
finally, I especially recommend the cert collection ccie rs dumps and very useful
for the exam.

Read More >>

    CCIE R&S v5.0 LAB Exam Format

    CCIE R&S v5.0 LAB exam include 3 models(TS、DIAG and CFG).
    The total score of lab exam is 100 points ,if you get 80% every model ,you will get your CCIE number.
    TS:TS total score is 24 points,TS have 10 tickets,There are 2 tickets is 4 points, 8 tickets is 2 points,if you get greater or equal to 20 points,you will pass.
    DIAG:DIAG total score is 6 points,DIAG have 6 tickets, if you get greater or equal to 4 points,you will pass.
    CFG:CFG total score is 70 points,CFG have 5 section, if you get greater or equal to 56 points,you will pass.

Enquire Now

    CCIE RS v5.0 LAB Examination Content

    1)TS:2 sets topology,TS1 TS2
    2)DIAG:8 sets
    3)CFG:3 sets topology,H1 CFG、H1+ CFG、H2 CFG、H2+ CFG、H3 CFG
    CCIE R&S LAB Dumps
SPOTO Collaboration CCNP Dumps Advantage
Quality and Value for the Collaboration CCNP Exam

SPOTO Practice Exams for Cisco CCNP Collaboration are written to the highest standards of technical accuracy, using only certified subject matter experts and published authors for development.

100% Guarantee to Pass Your Collaboration CCNP Exam

If you do not pass the Cisco CCNP Collaboration exam on your first attempt using our SPOTO testing engine, we will give you a full updated dumps for you.

VCE, Interactive Collaboration CCNP Testing engines

SPOTO Collaboration CCNP Preparation Material are researched and produced by Cisco Certification Experts who are constantly using industry experience to produce precise, and logical.

How to Pass Your Collaboration CCNP Exam Easily On The 1st Try with SPOTO questions and answers

Whether you are a student attempting to pass an exam to be eligible for a post-graduate job, or a working professional hoping to improve your work credentials and earn that dream promotion SPOTO is here to help. We have exam dumps and braindumps for CCNA certification, CCNP certification, CCIE certification, CISSP certification and many more. Passing an exam or certification is not an easy feat.
Our materials have been reviewed and approved by industry experts and individuals who have taken and passed these exams. SPOTO will have you prepared to take your test with high confidence and pass easily. Whether you are looking for a CCNA study guide, CCNP exam questions, CCIE exam dump or a CISSP test, SPOTO has you covered. You will be able to preview questions for any number of exams and certification tests within minutes of logging on. Each question is multiple choice, and offers the ability to see the answer right then and validate your understanding. Sign-Up for SPOTO today and start your journey towards certification.

  • cisco ccie routing and switching v5 0 troubleshooting practice labs - SPOTO CCIE CLUB

  • 1155 Reviews
  • The debug ppp negotiation command will give you much more output, so if youre just beginning troubleshooting on a PPP connection, run debug ppp authentication first - youll see immediately if theres a problem with the passwords. cisco ccie routing and switching v5 0 troubleshooting practice labs