ccie wireless lab location - SPOTO CCIE CLUB

    CCIE Wireless 400-351 Lab

    The CCIE Wireless Lab exam is made up of two modules:
  • 1: Diagnostic (the act or process of identifying the root cause)
  • 2: Configuration & Troubleshooting (implement and fix)

  • Get Dumps

Feedbacks More>>

Do you know how to solve TS /CFG problems?

There are not many problems with the exam. I will Just write something I think I need to pay
attention to. with the help of SPOTO club, i pass the exam once. If you want to know more details,
you can consult SPOTO club where there are many professionals. I will provide comprehensive
dumps and clear solutions.

1. User 4 trace Only when I come back to check, I find trace timeout
suddenly. In the beginning, it is good. but It is ping, not trace. R40 trace usser4 also works. Finally,
I reload user4, then the phenomenon is restored. So, if you have a chance, you still have to look
at what you have done.
2.MPLS backup. The backup enterprise is required to go to DMVPN. I take half an hour to try to
do this. I discover that DMVPN will become the primary route if I can’t use some ways. There is
no default route-map on r14. I remember that the teacher advises us not to write route-map. So
give up. Finally, I change the configuration back. only r51 OS has a devolved default route in TS. In
65005, master and standby can be distinguished by setting default-information to originate
metric-type. Do not know how to distinguish between primary and secondary in 65001. There is
no route-map preset on r14.

Layers 1 and 2 do require more attention. There is no SW mo acc, there is also the mouth of the
shutdown. Remember to take the time to check yourself.
2 many kids are missing. Take the time to look it up.
3.HSRP has been partially configured.
I want to give some confidence to many students like me who work full-time and have no time to
knock out the version on weekends. It is really important to watch the discussion in the group
and listen to the teachers teaching videos carefully. Many of the situations I encountered in the
exam room are solved in groups and by teachers. In addition, if there is no time for students, you
can try to take a week off work before the test or take participate in the model test. I always talk
to the teacher after the exam. My teacher has been very helpful to me. They help me understand
the test point. Finally, thank you very much for your help!


CCIE RS Lab solutions:TS2, DIAG2+, CFG 2+

Combination: TS2, DIAG2+, CFG 2+. Test location: BJ
Q1 Deny all by default, add one to release.
Q2 R14: next-version op-self
Q3 Did not solve it, give up decisively, R23 had a neighbor but did not receive the
route of 10.2.100/24, IGP checked no problem and BGP strategy was no problem,
Q4 The demand has indeed changed, not SERVER1, but SERVER2, the solution is
Q5 Change the network type of the tunnel to P2M. Note here that the R60
phenomenon map requires a route of I didn’t pay attention to it for the
first time. There is a problem with the tunnel IP address of R51 (/32).
Q6 Do Redis OSPF in R15 ipv6.
Q7 R1 did not announce the IGP; the RT import of R3 had a problem, I checked
R4/R6 and changed it to the correct one.
Q8 D version CP snooping, add a trust, and then remove the lease of D version CP.
Q9 Tunnel key is wrong
Q10 Supplement the R24’s outside configuration and add R25 in parallel. (The
address of telnet is

Just starting this, it’s really awkward, I don’t know what to do. Because you can’t
easily click “next”, I probably guessed that the answer might be DIAG2. After the
next question, I found that I can take a step forward.
Look at the picture and see the configuration.
Found that R2 has no route, R3 has a route.
After looking at the topology, I found that this topology was the opposite of the
version 2+ topology. I subconsciously thought it was version 2, but later confirmed
that there was a problem with R2, which was DIAG2+; the problem with R3 was
DIAG2. Decisively chose the answer of DIAG2+.
The capture file has a link at the bottom of the test interface. After you click it, it
will come out (the same as the cloud version ark given by the teacher).
Here, I personally analyze where the capture is very embarrassing. Filtering with the
version SRPV6 first does not work. It is filtered out using the version srp later. I have
been looking for a long time, I am very embarrassed, I don’t know which one to
choose. Finally, I stared at the FE80 package. Note that it is the src column. Don’t
find the dst column, confirm it and choose it. (The one of the FE80 that I chose dst
at the beginning).

CFG 2+
When I got the version, I was so happy that it was so simple!
OSPF is basically pre-configured. When configuring DR/BDR, pay attention to “cle ip ospf pro”.
BGP is also full, the router-id can be added up.
All of Corenetwork’s VRFs don’t have RDs.
JacobsCorp’s VRF is also equipped with its own.
————Pick up your sleeves and do it!
Maybe I knocked too fast. When I was typing 2.4 EBGP, I did all of MPLS, VPNV4,
VRF, and RT (version Q, Main office). I admire myself and dare to do this. I suggest
that you don’t do this like me. In the end, you still have to slash all the way and
stabilize! Because it is in this process, I was added to the wrong point by the
teacher, and I will talk about it in detail later!
When I did DMVPN, I didn’t have any “fragile ingredients”. It was just a casual
down, just add IPSEC.
Today, BJ’s Andy teacher is too strict. I will elaborate on my experience with TR (I
remembered it three times at first, then calmly thought about it not only three
The first place: The IGP of R15 is all gone. At this time, when I configured EBGP of
R15, I habitually checked the neighbors and configuration of IGP and found this

Note: Recovery after reconfiguration.
The second place: the IP address of R52 was changed (not pre-configured, because

I confirmed it is “up” when I configured).
Note: Recovery after reconfiguration.
The third place: the RD of the R52 was changed. Neighbors were all hanging, I
reconfigured them all.

Note: Recovery after reconfiguration.
The fourth place: R19’s DMVPN IPSEC strategy.
Note: Modify algorithm.
The fifth place: Multicast can’t come up. When I fix the configuration, I just added
the configuration, he removed it in the next second. (Change the global configuration of R17).
Note: Reconfigured, “shut” “no shut”, still does not work. In the end, I was
courageous and reloaded R17 directly. Restart the card for nearly 4 minutes,
fortunately, dmvpn is fine. Be sure to confirm the various configurations: Is the track
of IGP, NAT, SW3/SW4 recovered?
The sixth place: the EBGP status of R16 became idle.
Note: Recovery after reconfiguration.
Before the volume was handed over, I saved the windows one by one. I confirmed
the phenomena of the main and standby paths and the maps given by all the test
sites. But before the results came out, my heart was hung.
Finally, express my feelings, “Calmly take care of everything that happens, and have
a good mentality.” You have to understand the biscuit teacher’s problem-solving ideas.
Matters needing attention (personal position):
First, put the key equipment on the display, when all the configuration is checked,
put the key equipment in the lower part of the display and do a check in five
minutes! Avoid being TR and don’t know.
Second, the seat has two displays, it is recommended that you prepare for the split
screen operation during the preparation period. (Clicking on the device defaults to
the left screen, pulling all the questions to the right screen, making it a lot smoother)
Third, do not easily restart some important equipment, this is not recommended.
Because there are likely to be some unexpected situations!
Fourth, the night before the test, do not eat spicy food.
finally, I especially recommend the cert collection ccie rs dumps and very useful
for the exam.


CCIE Written LAB Exam Format.

1. CCIE Wireless V5.0 LAB Examination Content:

2. CCIE Wireless LAB Study Plan

3. CCIE Wireless LAB Solutions DEMO

Section 1:Network Infrastructure
Section 1.1 Troubleshoot the network at Headquarters so that for the connections between the 3650s and the 4500s, corporate wireless user traffic for VLANs 101 and 102 only, use G1/0/20 on the 3650s as the primary forwarding link. G1/0/21 on 3650-1 and 3650-2 must be used exclusively as a backup connection.
✔️Use an STP method that prioritizes how the local switches (that is, the 3650s) elect the root port.
✔️Configuration should be applied to the G1/0/21 interfaces only.
interface GigabitEthernet1/0/21
spanning-tree vlan (….) cost (…….)
interface GigabitEthernet1/0/21
spanning-tree vlan (….) cost (…….)

Section 1.2 Routing is not working as expected at Headquarters as not all subnets are reachable from the HQ switches. Troubleshoot this problem so that routing works between all lab subnets.
✔️Only static routing is permitted to solve this task. Do not use the “ip default-gateway” command.
  • ccie wireless lab location - SPOTO CCIE CLUB

  • 955 Reviews
  • Hence, if you know anyone, whether friend, family or co-worker who has taken a CISSP course before and was successful mainly as a result of the training reserved during the course, ask for a referral to the particular institution. ccie wireless lab location